A flotation rotor and stator are the rotating and stationary parts of the agitating mechanism in a mechanical flotation cell. The rotor spins at the bottom of the drive shaft, suspending solids and dispersing air; the stator is the fixed ring around it that shears air into fine bubbles and stabilises the pulp above. Between them they set bubble size, particle-bubble contact and therefore recovery. Because they work in abrasive slurry at high speed, they're replaced on a planned cycle as wear parts.
· Rotor = suspension + aeration; stator = shear + swirl removal. The pair functions only as a pair.
· Bubble surface area flux — the driver of flotation kinetics — is manufactured in the rotor-stator gap.
· Wear is silent. Recovery drift, falling air draw and sanding appear before any audible change — don't wait for noise.
· Rubber, polyurethane and ceramic composites trade impact resistance against profile stability.
· November 2026 project news (Cabacal Jameson cell orders in Brazil, Gunnison flotation test work in Arizona) confirms the mechanism remains the process heart of every new concentrator.
|
Item |
Rotor (Impeller) |
Stator |
|
Function |
Suspend solids, disperse air, create contact |
Shear bubbles, remove swirl, protect froth zone |
|
Mounting |
On the drive shaft |
On shaft (overhung) or tank floor |
|
Wear mode |
Profile rounding, blade loss |
Edge grooving, blade straightening |
|
Typical life |
3–12 months by duty |
Similar, often one rotor per stator change |
|
Materials |
Rubber, polyurethane, ceramic composite |
Rubber, polyurethane, ceramic composite |
|
Failure signal |
Falling air draw, sanding, recovery drift |
Coarsening bubbles, rising blower pressure |
In flotation vocabulary, "impeller" and "rotor" describe the same rotating assembly: a disc with radial or curved blades, often wearing a protective cover, bolted to the shaft end. The stator — sometimes called a diffuser or disperser — is the stationary ring of blades or baffles surrounding it. Self-aspirating machines such as classic XJK flotation cells and SF flotation cells draw air down the shaft by the rotor's own suction; forced-air machines such as XCF/KYF flotation cells receive low-pressure air from a blower through the shaft or standpipe. Either way, the dispersion work is done at the rotor-stator interface.
The rotor flings pulp outward through the stator at peripheral speeds of roughly 5–10 m/s. Air entering this zone is torn into bubbles of about 0.5–2 mm. The stator's blades intercept the tangential swirl and redirect the flow vertically, so bubbles rise through a quiescent zone into the froth instead of tearing it apart. Collision, attachment and survival — the three steps of every flotation separation — are each governed by a different part of this flow field: turbulence at the rotor edge sets collision rate, bubble size sets attachment efficiency, and the calm zone the stator creates protects particles already attached.
· Recovery leverage: a mechanism in spec produces the fine, abundant bubble population that floats both coarse and fine fractions.
· Energy control: fresh profiles pump efficiently, so the same agitation costs less power.
· Predictable maintenance: wear is gradual and measurable, so change-outs fit planned shutdowns.
· Retrofit gains: modern flotation impeller & stator profiles fitted to older flotation cells can lift recovery without new tanks.
The rotor-stator principle runs through every mainstream mechanical family: the XJK and SF self-aspirating cells common in mid-size plants, the XCF/KYF combination cells in larger forced-air installations, and Jameson-type contact cells that separate contact from cleaning — the type Meridian Mining ordered for Cabacal in November 2026. Duties span copper, lead-zinc, gold sulphide, phosphate and potash circuits, roughing through cleaning, and every one of them runs on parts from the flotation rotor & stator parts aftermarket.
|
Material |
Strength |
Weakness |
Best fit |
|
Natural rubber |
Impact tolerant, repairable, economical |
Profiles round faster |
Corrosive, moderately abrasive, fine-to-medium feed |
|
Polyurethane |
Holds moulded profile long |
Can crack under coarse impact |
Sharp, coarse, high-tonnage feed |
|
Rubber-ceramic composite |
Ceramic in the hottest zones |
Bond integrity is the new failure mode |
Extreme abrasion, large cells |
|
Duty |
Recommended mechanism focus |
|
Rougher, coarse siliceous feed |
Polyurethane or composite; inspect monthly |
|
Cleaner, fine gentle feed |
Rubber; longer cycles acceptable |
|
Self-aspirating small cells |
Rubber; check drawn-air volume weekly |
|
Large forced-air cells |
Composite zones on rotor edge; trend blower pressure |
|
Industry |
Typical use of rotor-stator mechanisms |
|
Copper |
Rougher/scavenger banks, large cells, high wear |
|
Gold sulphide |
Cleaner duties, fine bubbles prioritised |
|
Lead-zinc |
Multi-stage circuits, staged material choices |
|
Phosphate / potash |
Coarse flotation, abrasion-driven selection |
Start from the feed: size distribution, abrasiveness, solids density and pH. Coarse sharp feed argues for polyurethane or composite; corrosive fine feed suits rubber. Confirm the profile against the cell OEM drawing or a measured sample, and insist on a documented clearance limit so the next change-out has an objective trigger. Price matters most at the end of this sequence, not the start — and the flotation section of the catalogue maps every option.
Send cell model and size, rotor diameter and profile drawing or sample, material preference, duty description and — when available — photos of the worn parts. Reputable aftermarket flotation spares (rotor & stator) manufacturers produce to OEM drawings, quote wear-life expectations per material, and pack assemblies with shaft hardware so a change-out is a single shift.
1. Profile rounding. Clearance opens, bubbles coarsen, and fine recovery leaks first. It's the quiet one.
2. Blade loss. Sudden imbalance shows as vibration and rising power draw.
3. Bond failure on composites. Detached ceramic tiles race through the circuit; inspect bonds at every change.
4. Shaft hardware neglect. A loose rotor key lets the assembly fret and walk.
· W
Osoba kontaktowa: Mr. Maple
Tel: +86 17778255675
Faks: 86--311-80690567