logo
Dom
Produkty
O nas
Wycieczka po fabryce
Kontrola jakości
Skontaktuj się z nami
Poprosić o wycenę
Aktualności
TOGETHER HTL LTD
Dom Nowości

Need a Perforated Pre-Press Belt but Have No Drawing? Start with These 5 Details

Firma TOGETHER HTL LTD jest bardzo dobra, chętnie z Państwem współpracuję, bezpiecznie, wydajnie, profesjonalnie, uczciwie, szczęśliwie! Dziękuję za zapewnienie mi stabilnych usług i produktów. -----EUROPAT

—— EUROPT INDUSTRIAL

Im Online Czat teraz
firma Nowości
Need a Perforated Pre-Press Belt but Have No Drawing? Start with These 5 Details
najnowsze wiadomości o firmie Need a Perforated Pre-Press Belt but Have No Drawing? Start with These 5 Details

Are you searching for a perforated pre-press belt for an MDF, HDF or particleboard production line? What if the original technical drawing is missing ?


This is a familiar challenge for maintenance and purchasing teams. A replacement belt is needed, but the original supplier's records may be incomplete, and the old belt may already be worn or damaged.

Before giving up on the project, it helps to understand two things: why the belt is perforated and what information can be used to reproduce it.

Why Does a Pre-Press Belt Have Holes?

A loose wood-fiber or particle mat contains air between the raw materials after forming.

During pre-pressing, the mat is compressed to reduce its thickness and improve its stability before entering the hot press. At the same time, the air inside the mat needs a route to escape.

The openings in a perforated pre-press belt provide passages for air through the belt. When the belt is used with a suitable machine ventilation or extraction arrangement, the design can support air release during compression.

This is why the hole design is an important part of the belt specification, rather than just a visual feature.


What Should You Check Before Ordering?

A replacement belt should match the machine and working conditions. Here are five important points.

1. Overall belt dimensions

Confirm the belt width, total length or circumference, and thickness. If possible, provide both the measured dimensions and the machine's original specifications.

2. Hole diameter and spacing

The hole diameter, pitch, arrangement and distribution should be checked. If you cannot measure them precisely, take close-up photos with a ruler beside the holes.

3. Belt construction

The surface material, reinforcement structure and flexibility should suit the required pre-press application.

4. Joint details

Provide photos of the joint and confirm its position, construction and any special running requirements.

5. Machine and operating information

The machine model, pulley diameter, tensioning arrangement, operating speed and production material can all help with specification review.


Can a Replacement Be Made Without the Original Drawing?

Yes, in many cases the assessment can begin without a complete drawing.

The following materials are useful:

  • Machine manufacturer and model

  • Belt width, length or circumference, and thickness

  • Photos of the old belt from both sides

  • Close-up photos of the perforations and joint

  • Photos of the belt installed on the machine

  • Any previous quotation, specification sheet or purchase record

Based on these details, the belt construction and key dimensions can be reviewed. A proposed drawing can then be prepared for your confirmation before production.

Do Not Confuse a Perforated Belt with a Deaeration Belt

Both products are related to air management in wood-based panel production, but they may have different structures and installation positions.

A perforated pre-press belt supports mat conveying and compression while allowing air to pass through its openings.

A dedicated airing or deaeration belt is designed for airflow management in its own process position. The two should be selected according to the actual machine layout.

Related product information:


Pre-press Belt with Perforated

Pre-press Belt without Perforated

Deaeration Belt with Carbon Fiber

Deaeration Belt with Copper Wire


Send the Information You Have

You do not need to wait until every technical detail is available.

Start with the machine model, basic belt dimensions and clear photos. If the hole pattern or joint details are uncertain, these can be reviewed during the drawing-confirmation stage.

Are you replacing an existing perforated pre-press belt, or sourcing one for a new machine?

Share the information available, and the replacement specification can be reviewed step by step.

Pub Czas : 2026-11-15 15:52:10 >> lista aktualności
Szczegóły kontaktu
TOGETHER HTL LTD

Osoba kontaktowa: Mr. Maple

Tel: +86 17778255675

Faks: 86--311-80690567

Wyślij zapytanie bezpośrednio do nas (0 / 3000)