Are you looking for a replacement conveyor belt but unsure which joint type to choose? Is a Z-splice better than a spiral ring, double pin ring or steel clip joint?
The joint is an important part of an industrial conveyor belt. It connects the belt ends and must withstand continuous tension, bending, friction and repeated passage over pulleys.
In wood-based panel production, different belts work in different environments. Forming belts carry loose fibers or particles, pre-press belts operate under compression and tension, deaeration belts need suitable air permeability, and steam mesh belts must allow steam to pass through.
For this reason, joint selection should be based on the application rather than one joint type being used for every belt.
A Z-splice is produced by cutting the belt ends into an interlocking finger pattern and joining them to form a continuous belt.
Advantages:
Relatively smooth and flat joint profile
No raised steel fastener across the belt surface
Good running transition when correctly manufactured
Suitable for applications requiring a continuous contact surface
It is commonly selected for forming belts and pre-press belts, where stable conveying and a smooth belt surface are important.
For permeable belt constructions, the splice area should also be checked to ensure that the joint does not create an unacceptable restriction in the required airflow.
![]()
![]()
A spiral ring joint connects the two belt ends using spiral-shaped connecting elements. It is particularly relevant to compatible mesh and open-structure belts.
Advantages:
Suitable for selected woven mesh belt structures
Allows opening and reconnection when the installation design permits
Provides a practical connection for certain air- and steam-permeable belts
Can simplify installation where an endless belt is difficult to fit
Typical applications include:
Deaeration belts
Steam mesh belts
Intermediate belts
The spiral connector must be compatible with the belt thickness, mesh geometry, operating tension and pulley arrangement.
![]()
A double pin ring joint uses two pins passing through aligned loops at the belt ends.
Advantages:
Mechanical connection that can be opened for maintenance
Practical for installation in machines with limited access
Pins can be inspected and replaced where the design allows
Suitable for certain permeable mesh belts
It is an option for selected deaeration belts and steam mesh belts. The pin diameter, material, loop construction and joint strength should be confirmed according to the actual operating load.
![]()
An endless belt is supplied as a closed loop rather than being connected by a separate mechanical joint at the installation site.
Advantages:
Continuous running surface
No exposed metal fastener
No separate pin or spiral connector
Can be useful where surface continuity is important
An endless construction may be considered for certain deaeration belt applications. However, the machine must provide sufficient access for installation and replacement, and the belt must be manufactured to the required circumference.
A steel clip joint uses metal fasteners to connect the belt ends.
Advantages:
Fast installation
Convenient for field replacement
Practical for certain maintenance and repair situations
Does not require the same type of bonded splice process as a Z-splice
It is a suitable option for many bin bottom or storage belt applications, where convenient maintenance is often a priority.
However, steel clips create a raised mechanical connection. On belts that contact a fragile mat or require a smooth surface, the potential for joint marks, roller impact and localized wear should be considered.
![]()
| Belt type | Commonly considered joint |
|---|---|
| Forming belt | Z-splice |
| Pre-press belt | Z-splice |
| Deaeration belt | Z-splice, spiral ring, double pin ring, endless or steel clip, depending on design |
| Intermediate belt | Spiral ring |
| Steam mesh belt | Spiral ring or double pin ring |
| Bin bottom belt | Steel clip |
The table is a selection reference, not a fixed specification for every production line. The final design must be confirmed against the belt structure and machine requirements.
When requesting a quotation for a replacement belt, please provide:
Belt application and machine section
Belt width, length or circumference, and thickness
Existing joint type and close-up photos
Pulley diameters and operating speed
Working tension and installation arrangement
Whether air or steam must pass through the belt
Whether the belt can be installed as a closed loop or must be joined on site
For further product information:
Pre-press Belt without Perforated
Pre-press Belt with Perforated
Deaeration Belt with Carbon Fiber
Deaeration Belt with Copper Wire
There is no single joint that is best for every application. A smooth Z-splice may be suitable for one belt, while a spiral or pin connection may be more practical for another. A steel clip can be convenient for maintenance, while an endless belt can eliminate a separate mechanical fastener.
The best choice balances joint strength, surface requirements, permeability, installation access and operating conditions.
Need a replacement belt but are unsure about the joint?
Send us the belt dimensions, machine details and photos of the existing connection. We can review the application and recommend a suitable joint construction for confirmation.
Osoba kontaktowa: Mr. Maple
Tel: +86 17778255675
Faks: 86--311-80690567